FOSROC Conbextra GP2
Free-flow, high strength, non-shrink, cementitious precision grout
ADVANTAGES
- Gaseous expansion system compensates for shrinkage and settlement in the plastic state
- No metallic iron content to cause staining
- Pre-packed material overcomes onsite batching variations
- Develops high early strength without the use of chlorides
- High ultimate strength ensures the durability of the hardened grout
- Free flow ensures high level of contact with load bearing area
AREAS OF APPLICATION
- Typical applications would be the grouting of base plates and bolt pockets of turbines, compressors, boiler feed pumps and for bore packing
DOSAGE
- Water to powder ratio: Pourable=0.17 | Flowable 0.18
- Yield: Pourable -12.5 litres | Flowable - 13.3 litres
PACKING
- 25 kg bags
MIXING/USAGE
- The selected water content should be accurately measured and added to the mixer. The total content of the Conbextra GP2 bag should be slowly added and continuous mixing should take place for 5 minutes.
FOSROC Renderoc Plug
Rapid setting cement-based, water leak plugging mortar
ADVANTAGES
- Emergency water-stopping capability-sets in 8 to 10 seconds
- Single component-only the addition of clean water is required
- Excellent bond to the substrate
- Low exotherm-minimises thermal cracking
- Pre-packed formulation to overcome variation in site batching
- Contains no chloride admixtures
AREAS OF APPLICATION
- For the rapid temporary patching and plugging of concrete segments, concrete and brick tunnel linings, sewage system, below ground access chambers, pipes, basements, foundations and mines.
PACKING
- 1.5 and 15 kg bags
MIXING/USAGE
- Renderoc Plug should be added to clean water in the ratio of 3:1 respectively and placed immediately. One part clean water: 3 parts Renderoc Plug (measured by volume).
FOSROC Brushbond RFX
High performance two component elastomeric cementitious waterproof coating for roof, water tanks and reservoirs
ADVANTAGES
- Durable in all climate conditions and UV resistant
- Excellent barrier to carbon di-oxide, chloride and sulphate attack
- Allows water vapour to escape from the structure
- Good crack accommodation capacity
AREAS OF APPLICATION
- Brushbond RFX is suitable for all types of structures including those in coastal environments It is also suitable for water tanks, reservoirs, drainage culverts & basements
- Ideal water proof coating for roofs <500 sq.mts
COVERAGE
- 12-14m³ at 1 mm thickness (15 kg powder + 4.8 litre polymer liquid)
- 4-4.5 m² at 1 mm thickness (5 kg powder + 1.63 litre polymer liquid)
PACKING
- 15 kg powder + 4.8 litre polymer liquid (BB RFX powder BB RFX Liquid)
- + 5 kg powder + 1,63 litre polymer liquid (BB RFX powder+ B8 RFX Liquid)
MIXING/USAGE
- Brushbond RFX liquid is mixed with equal volume of water as per the proportion shown in the table and mixed with a slow speed drill. The powder component is added gradually to the liquid to avoid lump formation and mix for 2-4 minutes.
FOSROC Brushbond Roof Guard
High build fibre reinforced acrylic / single component waterproof coating for terraces without removing Brickbat Coba or Screed
ADVANTAGES
- High build system provides higher dry film thickness of more than 1 mm in three coats
- The product can be applied directly on existing sound concrete, brickbat Coba, screed concrete even without removal
- No protection screed required, eliminating the additional weight due to protection layer
- Excellent bond to concrete and masonry and UV resistant
AREAS OF APPLICATION
- Suitable for waterproofing of old and new roofs
COVERAGE
- 0.5 litre/m/coat (3 coat application is recommended)
PACKING
- 4 and 20 litre containers available in 4 colours: White, Green, Gray & Terracotta
MIXING/USAGE
- Apply Nitoprime AW primer (One liter of Nitoprime AW primer mixed with 500 ml water) followed by application of Brushbond Roof Guard in 3 coats to achieve total dry film thickness of 1 mm. The second and third coat of Brushbond Roof Guard shall be applied as soon as the first coat has reached touch dry state.
FOSROC Brushbond
Acrylic polymer modified two component elastomeric waterproofing membrane coating for concrete and masonry surfaces
ADVANTAGES
- Applied directly to the damp concrete and masonry
- Excellent adhesion and non-toxic
- Breathable, allows water vapour to escape
AREAS OF APPLICATION
- Ideal seamless waterproof coating for reservoirs, swimming pools and roofs <250 sq. mts.
COVERAGE
- 16-18 m' at 1 mm thickness (23 kg powder + 4 litre liquid)
- 4-4.5 m'at 1 mm thickness (6 kg powder + 1 litre liquid)
PACKING
- 23 kg powder + 4 litre liquid polymer pack
- 6 kg powder + 1 litre polymer pack
MIXING/USAGE
- Brushbond liquid is mixed with equal volume of water with a slow speed drill and the powder component is added gradually to the liquid to avoid lump formation and mix for 2-4 minutes. Keep on stirring during application.
Why Choose Us
- We have 43 year experience in waterproofing market.
- We use only high-quality materials made by industry experts..
- Our company follows the latest trends in equipment and process.
- Our staff is experts who upgrade their skills from year to year.
Get a Quote
Authorised Applicators for
